階梯形獨立根底：依據圖紙尺寸制造每一個階梯模板，支模次第由下至上逐層向上裝置，先裝置底層階梯模板，用斜撐和程度撐釘穩撐牢；核對模板墨線及標高，配合綁扎鋼筋及墊塊，再停止上一階模板裝置，重新核對墨線各部位尺寸。

　　并把斜撐、程度支撐以及拉桿加以釘緊、撐牢，最后檢查拉桿能否穩定，校核根底模板幾何尺寸及軸線位置，杯形獨立根底：與階梯形獨立根底類似，不同的是增加一個中心杯芯模，杯口上大下小略有斜度，心模裝置前應釘成整體，轎杠釘于兩側，中心杯芯模完成后要全面校核中心軸線和標高。

　　條形根底模板：側板和端頭板制成后，應先在基槽底彈出根底邊線和中心線，再把側板和端頭板對準邊線和中心線，用程度尺校正側板頂面程度，經檢測無誤差后，用斜撐、程度撐及拉撐釘牢，按圖紙尺寸制造柱模板（留意：外側板寬度要加大兩倍內側模板厚）后。

　　按放線位置釘好壓腳板再安柱模板，兩垂直向加斜拉頂撐，校正垂直度及柱頂對角線。裝置柱箍：柱箍應依據柱模尺寸，側壓力的大小等要素停止設計選擇（有木箍、鋼箍、鋼木箍等）。柱箍間距普通在500mm左右，柱截面較大時應設置柱中穿心螺絲，并計算肯定螺絲的直徑、間距。

標簽：